Alumax WA 40 Uživatelský manuál

05.11SHOWER DOOR2 PEOPLE REQUIREDIT IS MANDATORY TO HAVE A WALL STUD ON EACH SIDE OF THE SHOWER UNIT TO SECURELY FASTEN THE RAIL TO THE WALLS.KW006INS

INSTRUCTION MANUAL10Place temporarily the panel assembly on the threshold of the base on the line that was marked previously. Push wall brackets aga

INSTRUCTION MANUAL 11 WALL JAMB INSTALLATION Push the wall jamb against the wall. Level the glass panel assembly with the wall jamb.Lock into positio

INSTRUCTION MANUAL12Trace the position of the U channel (12) and of the bottom guide (17) on the threshold of the base. Mark the location of the botto

INSTRUCTION MANUAL13Replace the wall jamb against wall using the line previously marked as a guide. Level and mark locations of the four holes to be d

5bINSTRUCTION MANUAL14 WALL BRACKET BACK PLATE 5 WALL JAMB INSTALLATION (CONTINUED) 4Add silicone to the exterior bottom edge of the wall jamb.F

6aINSTRUCTION MANUAL 15 WALL BRACKET BACK PLATE (CONTINUED) 56 U-CHANNEL LOCATIONInsert one drop of silicone in each hole bored in the wall before

INSTRUCTION MANUAL167 BOTTOM GUIDE INSTALLATIONPlace bottom guide to the edge of the U-Channel .Center the front bottom guide channel to the center of

8a8b8cINSTRUCTION MANUAL 178Install the panel. Insert the running rail into the wall bracket back plates that were installed previously. Insert the

9aINSTRUCTION MANUAL189DOOR PANEL INSTALLATION 1022 24 212321Drill through the wall jamb a hole with the 1/8” drill bit, to perce through the e

11dINSTRUCTION MANUAL1911 DOOR GASKETS INSTALLATIONTemporarily install midgasket (5) and the door gasket (8) to door panel. Close door entirely, mark

2INSTRUCTION MANUALGENERAL INSTRUCTIONS Read this manual carefully and completely before proceeding. It is recommended that you wear safety glasse

6GASKETS12a14INTERIOR SHOWER SIDE INSTRUCTION MANUAL2012 ANTI-JUMP & DOOR STOPPERInstall Anti-Jump (14) in lower holes of door panel located bel

10INSTRUCTION MANUAL 21Place door receiver (15) against the wall, so eht otni ylhtooms sedils lenap rood eht tahtreceiver. Mark hole location. Remov

15aINSTRUCTION MANUAL22HOURS15 SEALINGSilicone the outside of the shower unit along the wall jamb and the exterior side of aluminum threshold and U

TOOLS AND MATERIAL REQUIRED RUBAN DOUBLE FACE VHB3INSTRUCTION MANUALDRILLSCREWDRIVERSLONG NOSE LOCKING PLIERSILICONEL BITSPENCIL CUT

10 16 13 17 1587ITEM PARTS QTY1WALL JAMB (REGULAR PUNCH) 12 FIXED PANEL 13 UNIVERSAL EXPANDER14FIXED PANEL GASKET15 MIDGASKET 16 DOOR PANEL 17 BOTTO

POSSIBLE CONFIGURATIONS 5INSTRUCTION MANUALRecommended door panel according to showerhead location. Choose right or left door opening, according with

VvVVDOOR PANEL ASSEMBLY 113113/8’’6INSTRUCTION MANUAL67DOOR HANDLE HOLESUse a mallet to install the bottom gasket (7) on

INSTRUCTION MANUAL 72RUNNING RAIL CARBOARD OR TOWEL TO PROTECTPlace door panel (6) inside the shower area to simplify following installation procedur

INSTRUCTION MANUAL8FIXED PANEL ASSEMBLY 19192Assemble the panel with the running rail. Align running rail holes with the holes of the panel. Inst

INSTRUCTION MANUAL 9FIXED PANEL ASSEMBLY (CONTINUED) 13Place U-channel (12) temporarily on the bottom of the panel (2). Slide the panel (2) pre-a